[Homeroast] Broken part on Gene Cafe

bruce ford brucewford at hotmail.com
Wed Jan 22 16:56:11 CST 2014


This is great info!  I will stick with my Behmor and not upgrade as I was 
considering!

-----Original Message----- 
From: Raymond Hays
Sent: Wednesday, January 22, 2014 2:28 PM
To: A list to discuss home coffee roasting. There are rules for this 
list,available at http://www.sweetmarias.com/maillistinfo.html
Subject: Re: [Homeroast] Broken part on Gene Cafe

Hello Sharon,

I had that happen to me
about two years and I was able to purchase a replacement from Fresh
Beans also could get a replacement heat unit, but now that Fresh Beans
has been replaced by Batch Coffee, run by  Derek and  we can no longer
get internal parts!  They list replacement parts on their web but not
much and they don't show your part. If you have a broken part you have
to send it in for repair. I need a heating unit, which is simple to
replace and I don't buy their explanation as to why we have to send the
roaster in for repair. I'm looking for a different roaster because I
will not go to the expense or waste time sending in the roaster for
repair.

This is what Derek said about replacemnet parts and who to contact if you 
are dissatisfied and want to
lodge a complaint.


Hello Raymond,
I understand your frustration.  We are not allowed to sell internal
parts for the Gene Cafe per instructions from the manufacturer, Genesis
Corporation.  The best contact email for them is sales at genecafe.co.kr
The decision to no longer sell internal parts was made by the
manufacturer because there were many instances of roaster parts being
incorrectly installed by home users.  This lead to many problems within
the US market.  When we took over importing in September, Genesis made
the decision to longer make the parts available for self-install.
With regards to Australia, I'm not sure how or why they sell parts.  Perhaps 
there is not a repair facility available in AUS, so they make
an accommodation and make the parts available.  Would you mind sending me 
the link?  I will ask Genesis for an
explanation.
Thanks for the input.
Best
Derek




On Wednesday, January 22, 2014 12:11 PM, sallsup <sallsup at gmail.com> wrote:

My Gene Cafe roaster had a parts failure, with a piece of plastic warping
and preventing the drum from rotating during the roast.  This unit has
given us hundreds of great roasts since September 2010, and I'd like to
keep it going.

My question is - will there be any major issue if I simply remove this bent
piece, but keep using the roaster until I can get a replacement part?  Is
the piece important from the standpoint of keeping heat out of the exit
gearing?

Details are:
The damaged part is one of the two skinny U-shaped strips of rigid black
plastic that lines the join between the sides of the roaster and the silver
reflective pan of the bottom.  These plug the gap between sides and bottom,
protecting the gearing from getting gunked up by dust and chaff.  It
probably provides some thermal protection as well, keeping some of the heat
coming off that drum away from the internals.

The one that's damaged is on the air-exit side of the unit (left side when
you are looking at the roaster from the front). About half of it is bent
out of the track.  It is rigid plastic and not letting me warp it back into
position.  I might be able to cut it in half but would be concerned about a
broken piece being jarred enough to poke into path of the drum (there's not
much clearance).

I'm not sure how it happened, but it looks as if that piece got jarred out
of alignment at the top of the "back".  When the next roast started, the
drum started rotating, hit the unaligned top of the piece after about a
quarter-turn, and pulled it out even further until after an inch or so, the
drum couldn't move and the unit went into error mode.  This was only
seconds into the roast so I was still there and immediately shut it down.
The temperature hadn't yet risen enough to require a cooling cycle.

It took a bit of jiggling the ends of the roaster, but I was able to get
the stuck bit out from under the drum (no easy feat with the heat shield
still on!).  I plugged in the unit again long enough to let it rotate the
drum back to the normal "done" position so it could be removed normally.
The frightening clack-clack noises didn't reappear as it rotated the drum
the remaining 3/4ths turn, so I'm figuring the gearing wasn't actually
damaged and the unit is fine.

Where it stands now is, the unit doesn't appear to have any damage other
than the warped piece.  I should be able to remove or cut off that piece.

Have any of you had this kind of problem before?  Any gotchas to removing
this piece (I have bookmarked Eddie's slideshow on taking apart the GC)

Who did you buy a replacement part from?  (Somewhere in my emails here I
have info for a place that has parts for FreshRoast and Gene Cafes ... used
them once before for a chaff wiper door problem and had great customer
service - I'll check into that tonight)

Thanks!

-Sharon
_______________________________________________
Homeroast mailing list
Homeroast at lists.sweetmariascoffee.com
http://lists.sweetmariascoffee.com/mailman/listinfo/homeroast_lists.sweetmariascoffee.com
<a href="http://www.sweetmariascoffee.com/forum/">Sweet Maria's Forum</a>
<a href="http://www.sweetmarias.com/library">Our new Coffee Library</a>
_______________________________________________
Homeroast mailing list
Homeroast at lists.sweetmariascoffee.com
http://lists.sweetmariascoffee.com/mailman/listinfo/homeroast_lists.sweetmariascoffee.com
<a href="http://www.sweetmariascoffee.com/forum/">Sweet Maria's Forum</a>
<a href="http://www.sweetmarias.com/library">Our new Coffee Library</a> 




More information about the Homeroast mailing list